First and foremost please please please remember water is F***ING heavy. I know it sounds stupid to say but it’s so easy to forget how fast it adds up. Is your shed wood floored? What is it sitting on?

Would you be comfortable grabbing a 50cm diameter boulder and placing (Not dropping) it on the floor and not have it buckle let alone break?

If yes then you might be alright.

MIGHT!

is the outlet 110? Check the fuse and not how many amps it’s rated for.

If it’s just you and you have at least 20 amps I would seriously consider one of those inflatable hot tubs.

You can get one from anywhere between $200 and $600 and they will work for that wattage AND distribute the water weight enough you won’t crack a concrete base, even a not too thin one.

If you are thinking of a cast iron tub or something similar maybe with higher walls or smaller footprint as the shed isn’t big enough for a hot tub then you need to seriously worry about that it will be sitting on.

Finally dumping the water once in a blue moon with 2 squirts of soap isn’t great but it will do minimal damage but 2 or 3 times per week is a LOT of water that will concentrate in a small area and if you plan on washing at all that adds to a lot more soap and detergents then you realize concentrating in your lawn.

Consider doing some filtering before you dump. Charcoal or sand to start and that will help quite a bit. It’ll mean very slow drain but you don’t really are about that do you?

Squint. Not even kidding, you squeeze it slightly.

Yeah, logical volumes has a teeny bit of overhead, same with RAID. both together means you can run older things but things that have a lot of textures loading you will see some drop.

So many.

Curse of Strahd in 3.5: Who knew Con damage to a mostly spell caster group could be dangerous not just once but 4 times. In comparison both fights were Strahd were a f**ing walk in the park.

More of a test game than an actual campaign: We were testing if a CR appropriate group of goblins with levels vs a group of players would play out for the players: Well as it turns out I suck at calculating CR so our first fight was 5 players vs 5 goblins level 15 (Same as players) plus 10 starting goblins. We adjusted it for a correct CR and it was still a massacre. Ambush is a HELL of an advantage.

Anything goes campaign. Well turns out anything goes for the DM too so Level 3 half colossal half minotaur barbarian opponent with a posse of gobs with a ballista safely away means players die every other round or so.

Logical volumes. it slows down IO on this setup but i don’t run IO intensive games. It allow me to just repartition and add drives as needed.

Oooooooh, I have one:

https://www.grrlpowercomic.com/archives/comic/grrl-power-759-its-evolutionary-my-dear-washington-post/

It’s like a 5 page spread for the whole spiel but this is the most relevant page.

The one thing i will add it that the eye thing primarily is super true and backed up by science as 20% of our brain is dedicated to visual functions and adding a third would make our heads very very hard to handle for almost 0 benefits.

You can’t slow down the head in specific spots but you can slow it down in general as well as setting a minimal layer time so that it pauses between layer and lets them cool.

Call me mister suspicious if you like but I have had this exact issue daily with Chrome since they started complaining about adblocking. And wouldn’t you know it, the moment any form of adblock is disabled it miraculously does not happen. I can also fix it by clearing my cache every day and restarting the browser. I would start with those steps.

Bit of both really. Ok, the bed tramming is normal, even GREAT printers need it done every few weeks or so. The physics and mechanical properties of how the bed is held down mean changes in temperatures and normal shifts even in an ACed house mean they loosen naturally a little every day and after a few weeks they will be bad enough someone who likes a really level bed will need to clear them again. After a few months any bed that isn’t welded down is going to need to be redone.

Z offset and bed auto level follow from that. You need to redo them when you do the tramming anyway.

I would say run your printer more often but that won’t fix it. You’re running against physics and nothing can stop that. Maybe you can store up prints for say 6 months and then do them all in a week or so and you only have to do this once?

I was given a Razer with blue because the guy who owned work in a small office with multiple people. I Got hooked but not bad enough i have more than i have computers to use them on.

Now I use the retro 9bit do for everyday and I have a 36% for when my kids force me to use only one hand.

And novel and audiobook all the way to the end of castle heterodyne which this game covers. Now for an actual ship date for backers.

Drew Hayes: Anything he wrote but Superpowereds are about 30 hours on average and there’s 4. Phil and Kaja Folio: Girl Genius.

I also don’t see The Martian on this page so adding it as a suggestion.

Suavamente for sure.

Rey and Finn burgeoning romance hinted at in FA. I really wish they had built on that. Successful or not I can live with but at least try.

Lifelong fan of SW. I have seen all of them up to Last Jedi. I have read all of the EU back when it was cannon. Never went to New Jedi Order. Because the emotions it brought me were pain and suffering. They kill Mara Jade. The only other bad ass female character in a series of 30+ books. What about Children of the Jedi? I mean the entire Trilogy is whiny 70’s sci fi emo writing all it’s own but that the Star Wars stamp was put on it just adds insult to injury.

“It was a Unicorn in the same way nanny Ogg was a Unident.”

Sorry about the late response, OK, brackets and cases for microcontrollers are actually great on a select mini. I agree with others that a Bambu would serve you great AND give you MUCH better finish etc… but the footprint of that thing is about twice that of the mini. I know of at least two prototype printers that are smaller BUT they are prototypes with all the faff that involves including troubleshooting them every time you move them.

Good luck.

How “not use it very often” are we talking about? The critical thing for any printer is first and foremost bed leveling. If you get something like an MP select mini The footprint is about 30cm^3. You can absolutely throw it in a box and just pull it out whenever BUT you will need about 30 minutes to relevel the bed just perfect and potentially run a test print. That said, this machine also only prints a 10cm^3 and it will handle PETG IF it’s been modded otherwise it’s PLA and that’s it.

Which segue nicely into my next question: What will you be printing? Models and minis? Functional parts? Random statues you find online of waifus? (Only slightly kidding)

This matters a LOT.

For the first: The mini will sorta work but not be great with details. Fort the second plan on a printer that can handle PETG at least. For the latter, you want to look into a resin printer. They WILL fit into a closet when emptied and cleaned BUT the cleaning process is both lengthy, tedious and potentially noxious and requires quite a bit of space so I didn’t even mention them in the first part.

How techy are you and what level of handheld are you willing to get them? Retropie comes with a built in shutdown timer and you can set up cron jobs remotely to shut down after a time or even at certain times. Down side: You need to know how to set them up AND you are not going to get a machine that runs the latest and greatest.

You could go all out and get them a steam deck and set up crons but that’s strictly local to the machine.

The piece probably left the build plate and stuck to the nozzle, got pushed in and melted. OP got lucky and it didn’t hit anything hard and cause his leveller to break.